Georges vangansen
Georges vangansen
  • Видео 114
  • Просмотров 122 282
Skywing Falcon second flight.
The second flight is mainly to test how the plane reacted to control inputs, all went smoothly, and did not find any bad behaviour at all, the 90-degree cross wind did not help in the landing approach, but it was still very controllable, so far so good.
Просмотров: 796

Видео

Skywing Falcon maiden!
Просмотров 1,6 тыс.11 месяцев назад
Skywing Falcon, guided by Mikado Vcontrol and dual Vbar Neo receiver. 3.5L fuel, 13.4 Kgs takeoff weight. very happy with this jet! It's easy to set up at the field with all the quick connections. fly as it should, with no bad tendencies.
Krill air craft. Mini Ares flight at the HKMEC
Просмотров 8902 года назад
Finally getting it a bit dialled in and starting to have some fun with it. Powered by KingTech K70, Guided by Mikado VControl radio.
Mirage 2000 flying in the sunset!
Просмотров 873 года назад
King Tech K130 prototype powered Vector thrust Mirage 2000 flying at HKMEC during a beautiful sunset!
Ares L Maiden
Просмотров 9753 года назад
This is how I maiden any plane, take off then after it's trimmed, I will fly it in dirty configurations and just fly landing sequence, many peoples make the mistake of flying a new plane with all kinds of aerobatics but omit the landing, and when it comes the time to land, they are in troubles.
FB Mirage 2000 vector thrust Maiden.
Просмотров 1843 года назад
First flight of my modified FB Mirage 2000 with vector thrust control. Kingtech K210G4 turbine, Vcontrol radio, twin Vbar neo receiver/Gyro.
Mirage 2000 Flat Spin flam out, dead spiral! can it be saved?
Просмотров 3443 года назад
Deliberated testing flam out in a flat spin, can it be saved? The first 2 try ended in crashes, what will happen on this one?
Unkillable Mirage 2000, take flight after 3 crashes.
Просмотров 1973 года назад
HSD MIrage 2000 at the HKMEC, this mirage has already had 3 crashes and it's still flying great!
Mirage 2000 half cuban 8 landing.
Просмотров 1123 года назад
HSD Mirage 2000 half Cuban 8 landing.
Maiden HSD Mirage 2000 desert camo VT.
Просмотров 4363 года назад
Powered by Kingtech K102 turbine, Mikado Vcontrol radio and Vbar Neo with Vplane app and vector thrust control.
Kingtech K102 test flights with Mirage 2000.
Просмотров 1 тыс.3 года назад
very fast throttle response, a joy to fly!!
Weathering T33 part 3
Просмотров 873 года назад
Weathering T33 part 3.
Weathering T33 part 2
Просмотров 893 года назад
Part 2 of the T33A weathering.
Weathering a Sky Master T33A RC jet.
Просмотров 3983 года назад
Some friends have been asking how I'm going to do the weathering on my T33A from Sky Master, so here is how I do it.
Fifth attempt at making red smoke oil
Просмотров 1124 года назад
Trying to make red smoke oil
Red smoke test 4 fail again.
Просмотров 694 года назад
Red smoke test 4 fail again.
The end of T one
Просмотров 3594 года назад
The end of T one
Mirage 2000VT RC Jet flight!
Просмотров 1744 года назад
Mirage 2000VT RC Jet flight!
Mirage 2000 rc Jet fun!!
Просмотров 2354 года назад
Mirage 2000 rc Jet fun!!
Mayday.. Mayday... flameout....
Просмотров 2264 года назад
Mayday.. Mayday... flameout....
How to set trim on motor switch
Просмотров 504 года назад
How to set trim on motor switch
MD 900 NOTAR visit HKMEC!
Просмотров 2604 года назад
MD 900 NOTAR visit HKMEC!
L39 3rd flight.
Просмотров 6684 года назад
L39 3rd flight.
Twin engine F18 Gear collapse on landing.
Просмотров 1534 года назад
Twin engine F18 Gear collapse on landing.
Mirage 2000 Thrust vectoring high alpha flight at HKMEC.
Просмотров 2464 года назад
Mirage 2000 Thrust vectoring high alpha flight at HKMEC.
Simon F18 Hornet flight at HKMEC.
Просмотров 894 года назад
Simon F18 Hornet flight at HKMEC.
T45 Jet maiden!
Просмотров 3664 года назад
T45 Jet maiden!
Mirage 2000 thrust vectoring high alpha flight.
Просмотров 1814 года назад
Mirage 2000 thrust vectoring high alpha flight.
SAB Avio Lizard 3rd flight!
Просмотров 6524 года назад
SAB Avio Lizard 3rd flight!
Lizard second flight
Просмотров 4454 года назад
Lizard second flight

Комментарии

  • @Reanimator82
    @Reanimator82 Месяц назад

    дайте пожалуйста ссылку на этот инструмент сьемник для подшипников

  • @Burnsey1977
    @Burnsey1977 4 месяца назад

    Did you ever figure it out?

  • @Burnsey1977
    @Burnsey1977 4 месяца назад

    Did you figure it out?

  • @3D-RC
    @3D-RC 6 месяцев назад

    What engine is on it?

  • @user-vasilis
    @user-vasilis 10 месяцев назад

    Very nice ! Where is your CG?

  • @hermestm62
    @hermestm62 11 месяцев назад

    Well done George!

  • @rachaelplant2504
    @rachaelplant2504 11 месяцев назад

    Well done Georges ! a far cry from the pilot who would kill 2 foam jets in a weekend ! Super professional and textbook flight ! Good Job !!!!!!!

  • @g33kfly
    @g33kfly Год назад

    Nice save!

  • @SkitzoFPV
    @SkitzoFPV 2 года назад

    Where did you get this jet?

    • @Georgesvangansen
      @Georgesvangansen 2 года назад

      From Hobby shop in Hong Kong, the Jet is made by HSD.

    • @SkitzoFPV
      @SkitzoFPV 2 года назад

      @@Georgesvangansen I don't believe they make this model anymore :(

    • @Georgesvangansen
      @Georgesvangansen 2 года назад

      @@SkitzoFPV I know for a fact that they still have stock of it.

  • @N2RIT
    @N2RIT 2 года назад

    Nice flying.

  • @leohcheung
    @leohcheung 2 года назад

    👏🏽👏🏽 Did you get the big Ares too?

  • @alixilviashah7166
    @alixilviashah7166 2 года назад

    Excellent job Georges

  • @rl56111
    @rl56111 2 года назад

    Failed landing

  • @Jetvlogger
    @Jetvlogger 3 года назад

    Flawless flying! turbine K85G4, what is your battery size? do you add extra weight for CG?

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      2S lipo 3000Mah, 3S Life 3000, 1 each, CG is 15 MM behind recommended, added about 150 grams of lead in the nose,

    • @Jetvlogger
      @Jetvlogger 3 года назад

      @@Georgesvangansen Thanks

    • @Jetvlogger
      @Jetvlogger 3 года назад

      @@Georgesvangansen what is your rate and expo ?

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      @@Jetvlogger Expo 100% on all surface. not sure about rate but bigger then recommended.

    • @Jetvlogger
      @Jetvlogger 3 года назад

      @@Georgesvangansen Thanks , i'm still waiting for mine.

  • @rachaelplant2504
    @rachaelplant2504 3 года назад

    Nice flying Georges ... you have a great style ,... ok the landing needs work but your a good jet pilot pleasing to watch x

  • @james34185
    @james34185 3 года назад

    Hi nice video. I watched your other videos too. I wanted to ask you, how much down elevator and/or vector elevator do you mix in with the flaps when you turn the flaps on to slow the jet down?

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      Not all jet use down elevator , some has up to compensate the flap, such as F16, F18, BVM bandit etc… its really airplane dependant. I will try from 3 to 5% mix then adjust according to how it fly.

    • @james34185
      @james34185 3 года назад

      @@Georgesvangansen Thanks. I guess I didn't say but I just purchased a Lizard jet myself and was wondering how you got it to fly so slow. Thanks!

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      @@james34185 Good luck and have fun, move CG 10MM to the front, will be easier to fly for the beginning.

    • @james34185
      @james34185 3 года назад

      @@Georgesvangansen Thanks!

  • @dwiggins9257
    @dwiggins9257 3 года назад

    😜 Promo>SM.

  • @vincentlee9044
    @vincentlee9044 3 года назад

    Very nice...TV version?

  • @Cloudy_Flyer
    @Cloudy_Flyer 3 года назад

    Very smooth flying 👌 gorgeous model to boot.

  • @vincentlee9044
    @vincentlee9044 3 года назад

    Nice flying...planning to install a SW80. You think SW120 will be a better choice? Do you use any gyro?

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      Thank you, if you are going to fly 3D, SW80 is too small, 120 will be ok, I'm using K130 prototype now, some of my club mate are using SW140.

    • @vincentlee9044
      @vincentlee9044 3 года назад

      @@Georgesvangansen Great, so I guess will need more nose weight to balance a bigger engine

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      @@vincentlee9044 just a bit, My CG is now 15MM behind the recommended point.

  • @leohcheung
    @leohcheung 3 года назад

    👍🏽👍🏽

  • @calebizsol
    @calebizsol 3 года назад

    Nice. Your setup and approach looked good. Slow her down (you were well above stall speed) and let her drop when she wants to. I have the same bird.

  • @prorafa2714
    @prorafa2714 3 года назад

    well done!

  • @awesomeuniverse3177
    @awesomeuniverse3177 3 года назад

    Great autorotation 😉

  • @GeenaTucker
    @GeenaTucker 3 года назад

    Great job getting it back under control and getting it down safely, Georges

  • @ScaleMeDown
    @ScaleMeDown 3 года назад

    Nice plane

  • @popeye7833
    @popeye7833 3 года назад

    seems to be difficult on approach landing ..little size i think

    • @Georgesvangansen
      @Georgesvangansen 3 года назад

      Not used to pull high alpha for landing on Maiden!

  • @abdullah2696
    @abdullah2696 3 года назад

    How many miles or hours can it go by 1 liter fuel ?

  • @abdullah2696
    @abdullah2696 3 года назад

    How many miles or hours can it fly by 1 liter fuel ?

  • @heavylidde
    @heavylidde 3 года назад

    do not fly so high the camera cannot follow 🤣

  • @topukgear
    @topukgear 3 года назад

    Very nice! Can you please share what size turbine you have in this please?

  • @adem-jet
    @adem-jet 3 года назад

    多才多藝,太專業啦

  • @leohcheung
    @leohcheung 3 года назад

    Gorgeous wing.

  • @rkelley8475
    @rkelley8475 4 года назад

    What size turbine

  • @UneducatedEngineer444
    @UneducatedEngineer444 4 года назад

    Back to the work bench! Turned everything red behind it though it looks like

  • @GeenaTucker
    @GeenaTucker 4 года назад

    Oh man. Sorry to see this. :(

  • @MrFishface5
    @MrFishface5 4 года назад

    he makes it look easy

    • @Georgesvangansen
      @Georgesvangansen 4 года назад

      it's an easy plane to fly! no bad tendency at all.

  • @najar80
    @najar80 4 года назад

    Nice Georges !!!

  • @frankmoradiellos5275
    @frankmoradiellos5275 4 года назад

    George’s You came in hot!!!

  • @Dogdocphil
    @Dogdocphil 4 года назад

    White Balance!!!

  • @najar80
    @najar80 4 года назад

    bravo georges

  • @GeenaTucker
    @GeenaTucker 4 года назад

    That was awesome, Georges. Thank you for sharing.:)

  • @GeenaTucker
    @GeenaTucker 4 года назад

    Nice flying Georges. :)

  • @NICHOLASRGLORIOSO
    @NICHOLASRGLORIOSO 4 года назад

    That was sweet bro!! :)

  • @philipschell6515
    @philipschell6515 4 года назад

    What engine are you running in there

  • @vonstervon4407
    @vonstervon4407 4 года назад

    You have a link or tutorial on how to install x45?

  • @gabrielsandoval9869
    @gabrielsandoval9869 4 года назад

    Nice smooth flight boss!

  • @boliu7920
    @boliu7920 5 лет назад

    Excellent flight! When you make the spinning movement, do you use full throttle. I am planning to buy this jet to learn fly vt. But i don't know the exact stick sequence to initiate the spinning movement and how to recover from the spinning to normal flight. Can you help me with that, or can you tell me where i can fine some reference. Thank you.

    • @Georgesvangansen
      @Georgesvangansen 5 лет назад

      bo liu , I’m no expert in this, I start the spin at nearly zero forward speed after a flip with full throttle and full rudder and up or down elevator depending on upright or inverted spin

    • @boliu7920
      @boliu7920 5 лет назад

      @@Georgesvangansen how do you recovery from spin? neutral the rudder and cut the throttle and let it fall to gain speed then level it out? i saw you did an inverted spin and transform to an inverted flight forward. do you practice it using some other means,like the simulator?

    • @Georgesvangansen
      @Georgesvangansen 5 лет назад

      bo liu just release rudder and slowly release elevator , don’t reduce throttle

    • @boliu7920
      @boliu7920 5 лет назад

      @@Georgesvangansen Do you mean when you do the spin, you also hold the elector to keep it level and when you want to get out of it, you slowly release it to let it gain vertical speed? Thank you.

    • @Georgesvangansen
      @Georgesvangansen 5 лет назад

      @@boliu7920 Yes. and I don't use simulator.

  • @Joelmelanie
    @Joelmelanie 5 лет назад

    what is the name of the club, nice flying

    • @Georgesvangansen
      @Georgesvangansen 5 лет назад

      Joel & Melanie Vlashof HKMEC

    • @Georgesvangansen
      @Georgesvangansen 5 лет назад

      www.google.com.hk/maps/place/Hong+Kong+Model+Engineering+Club/@22.414666,114.0413223,17z/data=!3m1!4b1!4m5!3m4!1s0x3403fa10558121f5:0x9c67a1430f4bbb1!8m2!3d22.4146611!4d114.043511

  • @janmodell1
    @janmodell1 5 лет назад

    Beautiful flying beautiful piloting. How big is Mirage, what is the weight, what a turbine, what a gyro?

    • @Georgesvangansen
      @Georgesvangansen 5 лет назад

      about 2 meter , 8.4Kgs with full 1.8L, Kingtech K85GII , Mikado Neo gyro.